Furnace Repair in Mount Prospect, IL

The first hard freeze of the season is when Mount Prospect phones start ringing. Furnaces that limped through November finally give out, and the homes hit hardest tend to be the mid-century properties near the downtown Metra district and the Randhurst area, where original ductwork meets a third or fourth generation furnace.

Leith Heating and Cooling Inc repairs heating systems throughout Mount Prospect with certified technicians, clear pricing, and no pressure to replace something that can be fixed.

Contact Us

Common Furnace Problems We See in Mount Prospect

Mount Prospect furnaces fail in patterns tied to how these homes were built and remodeled. Finished basements often choke off return air, which sends the whole system into overheat protection. Additions built onto 1950s and 1960s floor plans get tied into duct trunks that were never sized for the extra square footage, so back bedrooms stay cold while the furnace runs constantly.

Add decades of ignition cycling and the result is a familiar list. Failed igniters, dirty flame sensors, tripped limit switches, tired blower motors, and heat exchangers reaching the end of a long service life.

Same-Day Emergency Furnace Repair in Mount Prospect, IL

No heat in a Chicago-area January is an emergency, and we treat it that way. Mount Prospect no-heat calls go to the top of our dispatch list, and our technicians arrive stocked for the failures that actually cause winter breakdowns.

Most emergency visits end the same day. We diagnose the fault, quote the repair before we start, and get the system cycling properly again before we leave. If a part has to be ordered, we tell you exactly when and what it will cost rather than leaving you guessing.

Furnace Parts We Repair and Replace in Mount Prospect

A furnace is a chain of components, and any weak link stops the heat. We service every one of them:

  • Ignition systems including hot surface igniters and control modules
  • Flame sensors, burner assemblies, and gas manifolds
  • Blower motors, belts, wheels, and capacitors
  • Heat exchangers in both standard and high-efficiency furnaces
  • Gas valves, inducer motors, and pressure switches
  • Control boards, limit switches, and rollout safety devices

We replace what has failed and test the full cycle before calling the job finished.

How We Helped a Mount Prospect Homeowner Stay Warm

Karen in Mount Prospect had a furnace that would light, run about ninety seconds, then drop out. Our technician traced it to a flame sensor caked with carbon buildup and an inducer pressure switch hose that had collected condensate. He cleaned the sensor, cleared and reseated the hose, and ran the furnace through four complete cycles to confirm the fix. Full heat, same visit, no replacement needed.

Why Choose Leith Heating and Cooling Inc for Furnace Repair in Mount Prospect

There are plenty of HVAC companies in the northwest suburbs. Here is what Mount Prospect homeowners get with us:

  • NATE and EPA-certified technicians who diagnose before they quote
  • Upfront pricing with no charges added after the work is done
  • A veteran-owned, family-operated team that answers for its own work
  • A 100% Satisfaction Guarantee on every heating repair

We would rather earn the next call than push a replacement you do not need today.

Areas We Serve

Leith Heating and Cooling Inc provides furnace and heater repair across Mount Prospect and the neighboring Cook County suburbs. Our service area includes Arlington Heights, Des Plaines, Prospect Heights, Elk Grove Village, Wheeling, Park Ridge, and Rolling Meadows. From the neighborhoods around Randhurst to the older blocks near the downtown Metra station, we can typically reach your home the same day for urgent heating service.

Frequently Asked Questions

What are the first signs a Mount Prospect furnace is failing?
Watch for rooms that never reach the thermostat setting, new rattles or booms at startup, a burner that lights and drops out, and heating bills climbing without a change in weather. Any of those is worth a service call before the system quits on the coldest night of the year.
That usually points to airflow rather than the burner. A clogged filter, a slowing blower motor, closed or blocked registers, or undersized ductwork after a remodel will all leave the furnace running with nothing to show for it. We measure airflow to find which one it is.
It can. Many basement finishes cover or eliminate return air openings the furnace depends on. Starved for return air, the system overheats and trips its limit switch. Restoring proper return paths often resolves what looks like a furnace failure.

Yes. Condensing furnaces bring their own failure points, including clogged condensate drains, cracked PVC venting, and pressure switch faults tied to blocked intake or exhaust runs. Our technicians are trained and certified on both standard and high-efficiency equipment.

Once a year, in the fall, before the heating season starts. Annual service cleans the burners and sensor, inspects the heat exchanger, checks blower performance, and verifies every safety control. It is the single most effective way to avoid a midwinter no-heat call.

Contact Us